ABSTRACT The use of natural lignocellulosic fiber (NLF) biocomposites for the construction industry has been growing over the years, due to technical and environmental advantages. However, fiber-matrix incompatibility remains a major challenge. Various surface treatments have been investigated to improve fiber-matrix bonding, including sodium lignosulfonate (SLS), a potentially effective and environmentally friendly chemical. In this study, SLS treatment protocols were applied to piassava fibers to evaluate their influence on the fibers. Thermogravimetric Analysis (TG/DTG), X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM/EDS), Fourier-transform Infrared Spectroscopy (FTIR), moisture absorption measurements and tensile tests were performed to characterize the modifications. Results demonstrated, for the first time, the efficiency of SLS to remove extractives from the piassava surface. In general, partial degradation of the cellulosic structure was observed, noticeable by the slight drop in crystallinity index (from 42.80 to 39.82%), and an increase in the TG residual mass (from 21.35 to 31.90%), along with changes in DTG curves. However, a particular SLS treatment using ultrasonic bath was able to fully clean the surface preserving the cellulosic structure, and increasing the strength of fibers (from 386 ± 140 MPa to 524 ± 126 MPa).

The fique is a plant typical of the Colombian Andes, from which relatively common items are fabricated. One of these is woven fabric extensively applied in sackcloths. The mechanical strength of fique fabric have motivated recent investigations on possible reinforcement of polymer matrix composites. For this purpose its thermo-mechanical behavior was unveiled. In particular, dynamic mechanical analysis (DMA) of fique fabric reinforced polyester matrix composites disclosed improved viscoelastic behavior in association with change in the glass transition temperature. The present work extends this investigation to epoxy matrix, which is one of the most employed thermoset polymer for composite matrix. Fique fabric volumetric fractions of up to 50% are for the first time incorporated into epoxy composites. It was found that these incorporations significantly increased the viscoelastic stiffness of the composite, given by the storage modulus (E’), in the temperature interval from -50 to 170°C. An accentuated softening in viscoelastic stiffness was revealed for all composites above 75°C. Peaks in both the loss modulus (E”) and tangent delta (tan δ), respectively associated with the lower and upper limits of the glass transition temperature, were shifted towards higher temperatures with increasing amount of fique fabric.

Firearms threat has always been a matter of personal concern, especially to soldiers in armed conflicts as well as police officers and civilians involved with public security. A multilayered armor system (MAS) is intended to personal protection against high kinetic energy ammunition, such as that used in rifles. MAS layers are normally composed of a front ceramic followed by a layer that must show both high impact resistance and low weight. Usually, synthetic fiber fabrics, such as aramid in Kevlar® and ultra-high molecular weight polyethylene (UHMWP) in Dyneema® are commonly used as the second layer. Currently, composites reinforced with natural fibers are also being considered as second MAS layer due to their good performance associated with the advantages of being cheaper and environmentally friendly. The fique is a relatively unknown natural fiber extracted from leaves of a plant native of South American Andes. In the present work, fique fibers and fique fabrics incorporated in polyester composite plates with volume fraction of 10, 20 and 30% were ballistic tested. The calculated projectile loss of energy indicated a relatively large energy dissipation by the composite. The tested specimens were statistically treated by the Weibull analysis and were examined by scanning electron microscopy.

The great environmental impact caused by mineral production has forced mining and ornamental stone industries to acquire new concepts and technical solutions in order to develop eco-friendly and sustainable activities. In this context, this work aims to study the durability of soil-cement block with the incorporation of limestone residues from the processing of marble as an ornamental stone. Specimens were prepared with 30, 40 and 50 vol% of residues added to the soil-cement mixture and analyzed for their physical, chemical and mineralogical properties. After the curing period, the specimens were subjected to mechanical analysis and the established experimental program showed that the addition of residues in the mixture becomes feasible for the preparation of soil-cement blocks, exhibiting improved results when compare to a reference block without residues.